- MZ3: SR Motorsports Filter Size?
- How far can the MZR go?
- Mazdaspeed 3 mods list!
- Performance parts
- Which Boost Gauge location to go with.
- Lotek Gauge Pods
- $800 to spend
- Has anyone seen this gauge pod for the Speed3?
- before & after blow off valve upgrade
- Keep it or F*&$ it
- 100 plus octane unleaded - where?
- Sedan Exhaust on my Hatch?
- ms3 k&n air filter replacement
- Transmission shifts hard from 1st to 2nd...
- 1G DSM BOV (preferably crushed)
- New turbo manifold available for MS3/MS6
- AutoEXE TMIC vs ETS TMIC
- Can someone please help me out
- How much boost are you pushing?
- How to seal exhaust leaks?
- Coksport MS6 True 3" Exhaust
- Non-Fouler trick on a MSP?
- This looks promising
- Injen CAI -> SRI?
- Injectors
- Mazdaspeed 6 FMIC
- MSP dyno with AFC
- Good pricing on Mazdaspeed parts!
- Best "bang for your buck" on 3.0 mods and upgrades...
- MS3 owners beware: Race pipe woes...
- Rebuild rotory motor's "HERE"
- MS6, replace one muffler with straight pipe?
- Mazdaspeed 6 owners READ THIS!!!!!
- AWR 80 durometer
- Turbo bypass switch?
- Transmission fluid
- Engine vibration help?
- Spin-on filter conversion for Speed6/Speed3
- Bov?
- sok07 does it again! (MS3 replacement gas pedal)
- Anybody gonna get the COBB ACCESS PORT when it drops?
- Best place for Turbo II builds
- Turbo Discussion - Trim, efficiency, Blade design, and other complicated crap
- Performance/Technical Resources
- RX-7.... Rotary vs V8
- DIY Intercooler pipes for MSP
- Pulstar plugs GB?
- Aeroforce Gauges for the MS3/MS6
- My exhaust video...
- Sputter/hesitation fix?
- The Miata Build Thread (lots of *BIG* pics)
- ATP's bolt on GT3071R turbo MS3
- STi dyno tune results
- Synapse BOV GB?
- MS6 Turbine Tech Diff Mount
- Anyone with a MS3 getting a FMIC?
- Worlds first MS3 flashed ECU
- MS cai and cbe
- Cobb AP for MS3
- The official where the f is the Cobb AP thread
- Synapse proves MS3 owners claims of power increase with BOV
- 3 DashHawk datalogs
- unichip installed today on MSP
- 28 whp swapping bpv for bov speed3
- MS3 Problematic Alarm system...HELP!
- Turbo Timer
- COBBLE COBBLE?
- Turbo
- 302 in a Miata | aka Monster Miata
- Bolt ons or straight turbo?
- Where to buy a flange for the exhaust
- Motor Mount and BOV recommendations
- Grounding Kit
- Prosport Boost Guage - Where to mount?
- MS3 TMIC cooling fan?
- What gauges?
- CAI/SRI and MN Dealerships
- Mazdaspeed CAI to a SRI
- Air/Water Intercoolers?
- 30mpg ms3
- Synapse BOV
- Introduction and question
- Newbie here w/questions about 08.5 m3s
- CP-E full control reflash
- Fill with links to v8 swaps!
- Need some help car mods
- Car not hitting boost??
- msp afc v2 need help to install
- Cobb finally releases AP for MS6!
- '03 miata, whats the most it can handle.
- Battery relocation issues?
- DIY Oil Catch Can mod
- All Kinds of Stuff in Here
- DIY coolant overflow tank?
- First MS6 Upgrade?
- PLX Kiwi MPG
- COBB AP FTW
- MS6 Liquid to Air intercooler
- Prosport Oil Pressure Gauge Install - HELP!
- The most interesting article about DISIs I've read in awhile...
- COBB AccessTUNER PRO has been officially released!
- MS3 owners
- The brick wall for the MS3/6 guys.
- Stock shifter needs to go!
- Balance Shaft Delete? yes or no
- COBB tells Mazdaspeed/owners to F*&^ OFF! Basically
- MSP air-water intercooler project
- The Answer for ALL engine failures??
- Can I get your opinion on Street Units Motor Mount?
- A boost gauge before replacing BPV?
- project rexy
- MSP/Unichip is being tuned at RS Thurs 5/14
- Friend with a 2005 3 S looking for mod guidance
- My Intercooler Dilemma
- TWM Short Shifter- Stage 1 vs. Stage 2
- Fuel pump upgrade question
- MSP Hiboost FMIC Kit question
- Nitrous in a 2007 MS3
- Heavy Duty Street/ Strip 4-Puck Spring Clutch Kit
- Reached my first plateau...now what?
- Do you need new fuel pump internals?
- Some stuff I found on 247.
- CAI Loudness
- Cobb releases LC + FFS for the MS6
- PG v.3 Exhaust Mani
- Resonator Delete
- Forge BPV ping
- which exhaust system
- Next Upgrade
- Mazda Rotory performance Shop in MN Burnsville.
- Re: Rotor problem
- Need a ms6 and ms3 for BCS bracket fitment testing
- New Mods on the way
- Toms 2010 gonna be broke and probably divorced mod extravaganza!
- My Miata Project
- Group Buy - James Barone Racing Short Throw Shift Plate
- DIY/Custom/Homemade Leather Shift boot
- Cheap sound?
- Refurbishing my shift knob
- 2010 MS3 Intake
- Hypertech + SRI = :D
- Coil ignition engine
- Any MS3 owners with aftermarket turbo inlet pipe?
- '03 miata, need new catback/muffler. suggestions?
- Your Winter 2010 - Spring 2011 Plans
- Engine goes BOOM!
- Install CAI before winter?
- 03 MSP Valve Adjustment
- Motor Mounts & Inlets
- In the market for new performance parts? Check out CP-e's Winter Sale!
- oil filter
- E85 conversion questions
- Turbo's 101 Class
- the big ? around suspension
- ARP main stud kit catalog number? (sanity check)
- What's new for the MZR 2.3L DISI engine?
- Align honing?
- Prototype MSP engine brace.
- Flexible/Adjustable radiator hoses
- How To: H&R Coilover install on Mazdaspeed 3
- MS6 Drop Springs
- How To: Camber Arm install on Mazdaspeed 3
- HELP! 17mm LCA bolt is effing me over!
- hehe you said rods
- hehe you said head work